XGSM Iași — Service & Piese GSM

Special modes

Phone stuck on the logo: what you can try without losing data

A logo that won't leave the screen means the system can't finish starting up — but your photos and messages are, most of the time, still on the phone. The golden rule: try fixes in the order that can't erase anything, and don't jump straight to a reset. Below is that order, step by step, for each brand.
Needs care30 minAndroidSamsungXiaomiHuaweiMotorolaGoogle PixelOnePlusOppoiPhoneChecked: November 17, 2026

Short version

  • Give it time first: after an update, the logo can legitimately sit there 30 minutes to 2 hours — plug it in.
  • Force restart for your brand: Samsung side key + Volume down over 7 s, Pixel Power up to 60 s, Xiaomi Power over 10 s, iPhone Volume up → Volume down → hold the side button.
  • Then safe mode (Android): hold Volume down while it starts — if it boots, an app is the culprit.
  • In recovery (Android), try only Reboot system now and Wipe cache partition — they erase nothing; “Wipe data” erases EVERYTHING.
  • Have a backup? A reset is a fair option. Don't, and the photos matter? Stop and ask about data recovery first.

Why it stops on the logo

The maker's logo shows on every start while the system loads — usually under a minute. When it sits there for many minutes, or the phone keeps restarting onto it again and again (a “boot loop”), start-up is failing somewhere along the way. The good news: being stuck on the logo usually affects booting, not your data — it is still there, the phone just can't reach it.

  • An interrupted or bad update — the most common cause: system files are left half-written and start-up can't finish.
  • Nearly full storage — Google warns a phone can misbehave when free space drops below 10%.
  • A bad app — especially one installed or updated just before the first freeze.
  • A worn battery — start-up draws the most power, and a tired battery gives up right then.
  • Liquid or a drop — corrosion or a shifted part inside stops the boot halfway.
  • A hardware fault — the storage chip or the motherboard; no button combo fixes that.

Note· After an update, give it time

A sitting logo is not always a failure: Xiaomi writes that after an update the phone processes a lot of data and may stay on the start screen for 30 to 120 minutes, and Apple says the progress bar can stand still for over an hour during a restore or migration. Plug it in and wait before intervening — it often finishes on its own.

The order that keeps your data

The secret is the order: start with what cannot erase anything and only go as far as needed. Each step below either starts the phone or tells you something useful — and you stop at the first one that works.

Phone screen: Samsung Galaxy

The screen holding you hostage: the logo should disappear within a minute. Sitting for long or coming back again and again? The system can't finish starting.
  1. Step 1

    Force restart — the button combo that cuts power. Does not touch data.

  2. Step 2

    30 minutes on a charger, plus removing the case, SD card and SIM tray. Does not touch data.

  3. Step 3

    Safe mode — the test showing whether an app you installed is the culprit. Does not touch data.

  4. Step 4

    The recovery menu: only “Reboot system now” and “Wipe cache partition”. They erase nothing — the other options can.

  5. Step 5

    Repair from a computer: Update on iPhone, the Pixel Repair Tool, Update in Smart Switch. Usually keeps data.

  6. ⚠ The red line

    From here down data is erased: “Wipe data” in recovery, a factory reset, “Restore” on iPhone.

  7. Before the red line

    No backup and the photos matter? Stop here and ask a data recovery service.

Step 1: force restart

A force restart cuts power from the buttons — the modern equivalent of pulling the battery. It erases nothing: Samsung states it plainly on its help page (“a forced restart will not erase any information from the phone”). It gets the phone out of a momentary freeze; if the system is corrupt it will return to the logo, and you move on to the next step.

  1. Hold Side key + Volume down for over 7 seconds

    Hold the side key and the Volume down key at the same time for more than 7 seconds. The phone vibrates, the screen goes off, then the Samsung logo appears — release then.

    If it enters the maintenance boot mode instead of restarting, pick Normal boot with the volume keys and confirm with the side key.

    1. 1Hold both for over 7 secondsPowerVolume down8 s

    Press the phone's physical buttons in the numbered order. 1. Hold both for over 7 seconds (Power + Volume down, 8 s)

For the other brands the combos are in the forced restart guide: on Huawei hold Power for 10–15 seconds (Power + Volume down for over 10 seconds on EMUI 11+ models), on Motorola Power for 10–20 seconds, and on OnePlus, Oppo and Realme Power + Volume up for about 10 seconds.

Tip

Back on the logo whatever you do? That is still information, not a failure: it means this is not a momentary freeze, and you move on to step 2.

Step 2: a real charge and less baggage

  1. Charge it for 30 minutes with a good charger

    Start-up is the moment of highest power draw, and a borderline battery can stop the phone right on the logo. Samsung recommends the original or a certified charger and checking the cable and adapter first. With the cable still connected, retry the force restart from step 1.

    Phone
    Charger
    Wall socket

    Connection: Phone via USB-C → Charger. Charger via power → Wall socket.

  2. Remove the case and check the buttons

    A case pressing constantly on the power or volume keys can hold the phone in a restart loop. Press each button a few times — it should spring back, not stay stuck.

  3. Remove the SD card and the SIM tray

    A faulty SD card can stop the phone from starting — Huawei asks for it to be removed even for updates. Take the SIM tray out too: you remove one more variable and can check the liquid-damage indicator at the same time (the marker inside the tray slot is white when dry; after water it turns pink, purple or red, per Samsung).

    Put the card and SIM back only after the phone has started normally.

Warning· Was it in water, or swollen?

Don't charge it and don't restart it at all. Current plus water means a short circuit, and a swollen battery is never pressed or charged — straight to a repair shop, carefully.

Step 3: safe mode

If the phone gets past the logo sometimes, or the trouble began right after a new app, suspect number one is the software you installed. Safe mode starts Android with only the system apps — if it runs fine that way, a downloaded app is to blame, which is how Google and Samsung tell you to catch it.

  1. Hold Volume down while it starts

    With the phone off, power it on and, the moment the logo or boot animation appears, hold Volume down until it finishes starting. On Samsung, Pixel, Motorola and near-stock Android this goes straight into safe mode — look for the label in the bottom corner of the screen.

    PhoneMessagesChromeCamera
    Safe mode

    Phone screen: Safe mode

  2. On Xiaomi, from the Mi Recovery menu

    Hold Power + Volume up at start-up until Mi Recovery appears, then pick the Safe Mode entry (on models that have it) — the route Xiaomi itself describes on its help page.

  3. It started in safe mode? Remove recent apps

    Uninstall the apps installed or updated just before the freeze, one by one — with a normal restart and a check after each. When the freeze stops, you found the culprit; Google warns that reinstalling the same app can bring the problem back.

Note

Still can't get past the logo even in safe mode? Then it's not (only) an app's fault — continue with step 4. Every entry route is covered in the safe mode guide. The iPhone has no user-facing safe mode.

Step 4: recovery — only the options that don't erase

Recovery is the English-text menu started from the buttons before the system loads — you move with the volume keys and choose with Power. Browsing the menu changes nothing. How to enter on each brand is in the recovery mode guide; in short: Samsung holds Volume up + Side key (on recent models, with the USB cable connected to a powered-on computer), Pixel and Motorola Volume down + Power then “Recovery mode”, Xiaomi and Huawei Volume up + Power.

From the menu you can pick safely: Reboot system now (a clean restart) and, where it exists, Wipe cache partition — it clears only the system's temporary files and is the classic advice after a bad update. Careful: it isn't everywhere — it's missing on recent Pixels and from Xiaomi's Mi Recovery (where the only “clean-up” option is a full wipe). On Samsungs with older One UI you may also find Repair apps, an app re-optimisation removed on newer versions.

Samsung Recovery
Reboot system now
Reboot to bootloader
Apply update from ADB
Apply update from SD card
Wipe data/factory reset
Wipe cache partition
Mount /system
View recovery logs
Run graphics test
Run locale test
Repair apps
Power off
Volume up/down = move • Power = select

Phone screen: Samsung Recovery. Reboot system now, Reboot to bootloader, Apply update from ADB, Apply update from SD card, Wipe data/factory reset, Wipe cache partition, Mount /system, View recovery logs, Run graphics test, Run locale test, Repair apps, Power off. Volume up/down = move • Power = select

On Samsung the menu is always in English. “Wipe cache partition” clears only system temp files; the line above it, “Wipe data/factory reset”, erases everything.

Danger· The menu's red line

“Wipe data/factory reset”, “Wipe Data”, “Clear data” and “Format data” erase absolutely everything — photos, messages, apps — and the phone asks for the account that was on it at start-up. On Huawei, mind this too: the “Download latest version and restore” option in eRecovery also erases data, per Huawei's own documentation. This is where you stop if you have no backup.

Step 5: repairing the system from a computer

A few makers have official computer tools that rewrite the system while usually keeping data — each one describes what it keeps, and the same tool typically also has a mode that erases everything. Read every screen before confirming.

  1. Connect it to a computer and put it in recovery mode

    Use the original cable and open Finder (Mac) or Apple Devices / iTunes (PC). Redo the force-restart sequence, but don't release the side button at the Apple logo — hold it until the cable-to-computer screen appears. The steps per model are in the recovery and DFU guide.

  2. When the computer asks, choose Update

    The computer detects the phone and offers two choices: Update reinstalls iOS over the broken one and keeps your data — Apple recommends it first. Restore erases everything permanently. If the download takes more than ~15 minutes and the phone leaves the cable screen, redo the sequence after the download finishes.

    iPhone

    There is a problem with the iPhone “iPhone” that requires it to be updated or restored.

    CancelRestoreUpdate

    Phone screen: iPhone. There is a problem with the iPhone “iPhone” that requires it to be updated or restored. [Cancel] [Restore] [Update]

Danger· Read the words before you confirm

On repair-tool screens, update usually keeps data, while restore / reinstall / rescue / wipe / erase deletes it. If a screen doesn't say clearly what is kept, don't confirm — stop and get a second opinion.

Signs it's hardware, not software

A software blockage is usually beaten by the steps above. When it isn't, the phone's history says more than the buttons:

  • It fell or sat in water before the first freeze — corrosion keeps working for days after the incident.
  • It heats up on the logo and dies — not restarting, dying. Xiaomi says to unplug the charger and see a service centre if it heats abnormally.
  • It started after the battery went bad — dying at 20–30%, draining overnight, or swelling.
  • It won't boot even after a full system rewrite — then the internal storage or the board is the suspect.
  • On Xiaomi it sits on the Mi logo for a long time with no text at the bottom — the official page says it plainly: service centre.

A phone that dies on the logo (doesn't restart — powers off completely) is more likely a battery or board problem than a software one. Those are told apart on a repair bench in minutes — a lab power supply shows instantly whether the board draws normal current.

The final decision: reset it, or take it in?

Once you've exhausted the safe steps, two roads remain — and the right one depends on a single question: do you have a recent backup? If your photos, contacts and WhatsApp also live in Google, iCloud, your Samsung account or on a card/computer, a factory reset is a fair option: the phone comes back clean and you restore your data during setup.

Danger· No backup, no erasing

If the photos exist only on the phone, do not reset and do not pick “Restore”: once erased, they cannot be brought back. A data-recovery service can read the memory even on a phone that won't start — start with data recovery, not with the reset. A rewrite that erases closes that door for good.
What you tried, what happened, what's next
You triedResultNext step
Force restartStarts and worksDone — check why it froze (storage, apps, battery)
Force restartBack on the logo30 minutes of charging + remove case, card, SIM
Safe modeBoots without freezingUninstall recently added apps, one by one
Safe modeStill on the logoRecovery: Reboot system now, then Wipe cache (where it exists)
RecoveryBoots after Wipe cacheWatch it for a few days; make a backup now
Computer toolThe update succeedsDone — back up regularly from now on
Everything aboveNothing gets past the logoBackup → factory reset; no backup → data-recovery service

What a repair shop does differently: it diagnoses first (battery, board, storage chip), reads the memory with dedicated tools even when the phone won't boot, and only then repairs. Tell the technician in your first sentence that the data matters — it changes the order of work: securing the data first, the repair second.

Mistakes that cost data

Do

  • Give it 30 minutes on a good charger before any conclusion.
  • Count the seconds on the button combos — 7, 10, even 60 seconds on Pixel.
  • Note exactly what happens: sits on the logo, restarts, dies — it helps the diagnosis.
  • Say “the data matters” from the start — at the repair shop and in any repair tool.

Don't

  • Don't reset “to see if it works” without a backup — there's no way back.
  • Don't let it restart-loop for hours — it heats up and wears the memory.
  • Don't install “phone repair” programs from unknown sites — many promise what they can't deliver, or charge for what the official tool does free.
  • Don't charge or restart it if it's wet or the battery is swollen.

Frequently asked questions

Why does my phone restart onto the logo forever?
That's called a boot loop: the system can't finish starting and begins again. The usual causes are an interrupted update, nearly full storage, a problem app or a worn part (battery, storage chip). Work through the guide's steps in order — from force restart to recovery — and see where it stops.
Will I lose my photos with a force restart?
No. A force restart only cuts the power — the equivalent of removing the battery — and Samsung states plainly that, done correctly, it erases no information from the phone. Data is only lost on options with “wipe”, “format”, “restore” or “reset” in the name.
How long is it normal for the logo to sit after an update?
Longer than you'd think: Xiaomi says post-update data processing can take 30 to 120 minutes, and Apple warns the progress bar can stand still for over an hour during a restore or migration. Plug it in and give it at least an hour before intervening.
What does “Wipe cache partition” mean? Does it delete my photos?
No — it clears only the system's temporary files, not photos, messages or apps. It's the option worth trying after a bad update, but it doesn't exist everywhere: it's missing on recent Pixels and in Xiaomi's Mi Recovery.
Is there a tool that repairs the phone without erasing data?
Yes, at some makers: on iPhone the Update option in recovery mode reinstalls iOS keeping data, the Pixel Repair Tool can fix software without a reset, and Smart Switch offers Update on Samsung. The same tools also have modes that erase everything — read every screen.
I've tried everything and it's still on the logo — can my photos be saved?
Most of the time yes, as long as you haven't erased anything. A data-recovery service can read the internal memory even on a phone that won't boot — what matters is not rewriting or resetting first. See the details on data recovery.
The phone dies completely on the logo instead of restarting — still software?
Probably not: dying outright at start-up is a typical sign of a worn battery or a board problem. A lab power-supply test on the bench settles in minutes whether it's hardware — and saves hours of software attempts.

Does your phone look different, or is something missing here?

Menus and buttons differ from model to model and change with updates. If these steps do not match your phone or you cannot find what you need, tell us your model and what you see on the screen: we will answer you and update the guide.

Checked against

Phone still not responding?

If no special mode helps, we check it on the bench and tell you what's wrong.