XGSM Iași — Service & Piese GSM

First aid

Phone won't charge, or charges slowly

Most phones that “won't charge” have a mundane problem: another cable, another socket or the lint packed in the port solves most of them. Work through the steps below in order — from the two-minute checks to the signs that the port or the battery needs a technician.
Anyone can do it20 minAndroidSamsungXiaomiHuaweiMotorolaGoogle PixelOnePlusOppoiPhoneChecked: November 17, 2026

Short version

  • Swap the socket, cable and charger — and push the plug all the way in. It solves most cases.
  • Shine a torch into the port: the lint packed inside is the number one cause. Fish it out with a wooden pick, phone powered off.
  • A “liquid detected” alert? Unplug both ends of the cable and let it dry — it can take up to a day. Wireless charging works meanwhile.
  • Stops at 80%? Not a fault — it's a battery protection setting you can change.
  • Only charges at a certain angle, or the percentage drops while plugged in? Worn port or battery — a job for a technician.

First: the two-minute checks

Between the socket and the phone there are three links — the outlet, the charger and the cable — and any of them can fail. Before anything else, rule them out one by one, because testing them costs nothing.

0 of 6 done

The socket
The charger
The phone

Connection: The socket via the mains → The charger. The charger via dead cable (broken) → The phone.

If any of the three links is dead — socket, charger or cable — the phone gets no power. Test each by swapping in one that works.

Tip· Completely flat battery?

The battery icon or a blinking light can take ~30 minutes of charging to appear — Apple gives the same ballpark. Only then is it worth trying to power on.

Lint in the port: the number one cause

The port sits open in your pocket all day and collects lint, dust and crumbs. The layer gets compacted with every plug-in until the plug can no longer reach the contacts. Samsung calls dirt in the port one of the most frequent causes of charging problems — and in a repair shop it's the first thing checked.

Typical signs: the plug doesn't go all the way in, sits loose, charging starts and stops by itself, or works only while you hold the cable to one side.

  1. Power the phone off

    Work on the contacts with the phone off — you want no current on the pins you're touching.

  2. Shine a torch into the port

    The torch on a second phone is the handiest. If you see a dark grey layer packed at the bottom, you've found the culprit.

  3. Blow gentle air into the port

    Samsung's official advice for visible dust and lint. Hold the phone with the port facing down so the debris falls out, not deeper in.

  4. Fish the rest out with a wooden or plastic pick

    A wooden toothpick or a thin plastic pick, short strokes outwards, never pressing on the centre tongue. Years-old compacted lint comes out in chunks, not fluff.

    A soft, dry toothbrush does the same job if there's no pick at hand.

  5. Reconnect firmly and check

    The plug should go in fully and sit tight. If charging now runs steadily, you've fixed the most common “fault” seen in repair shops.

Warning· What never goes in the port

Nothing metal — pins and paperclips scratch or permanently bend the contacts. No liquids — alcohol and sprays leave residue or short the wet pins. And no high-pressure compressed air: it pushes the lint deeper, not out.

A full port-and-speaker clean, step by step with what to avoid, is in the port and speaker cleaning guide.

The “liquid detected” warning

Recent phones refuse to charge when they sense moisture in the port — it's protection, not a fault. On iPhone XS, XR and newer you'll see “Liquid Detected” or “Charging Not Available”, and on Samsung a water-drop icon appears while charging stops until the port is dry. All of them say the same thing: current on wet pins corrodes them.

PhoneMessagesChromeCamera
Liquid Detected in USB-C Connector

Disconnect to allow the connector to dry. This may take several hours.

OK

Phone screen: Liquid Detected in USB-C Connector. Disconnect to allow the connector to dry. This may take several hours. [OK]

The alert blocks cable charging and accessories until the connector is dry — this is how it looks on iPhone XS, XR or newer.
  • Unplug the cable from the phone and from the charger — Apple is explicit: don't plug it back until everything is dry.
  • With the port facing down, tap the phone gently against your palm to get the excess liquid out, then leave it somewhere dry and ventilated.
  • After at least 30 minutes, try again. If the alert returns, there's still liquid in the connector or under the cable pins — a full dry can take up to 24 hours.
  • Does the alert appear only with one specific cable or accessory? That accessory is probably the culprit, not the phone — try another one.
The phone
Wireless charger

Connection: The phone via no cable → Wireless charger.

Meanwhile: wireless charging skips the port entirely. On iPhone it works once the back is dry — the cable stays off-limits until the connector is.

Warning· There's a way around it — at a price

On iPhone you can override the liquid detection and charge anyway in an emergency: reconnect the cable and choose the emergency option in the alert. Apple is explicit, though: charging with a wet connector corrodes the pins and can destroy the port for good. Use it only in a genuine emergency.

Stops at 80%? That's protection, not a fault

If the phone always stops at 80% (or at 85–95%), a battery protection feature is almost certainly on — set by you, by a family member, or switched on by an update. Every major maker ships one, because the battery suffers most when it sits at 100% for hours. Here's where it lives on each.

  1. Open Settings → Battery → Battery protection

    On One UI 6.1 and newer you get three protection modes; on older versions there was only an 85% limit.

  2. Pick a mode or switch it off

    Basic stops at 100% and resumes at 95%. Maximum stops at the limit you pick — 80, 85, 90 or 95% on One UI 7 or newer; on One UI 6.1 it was fixed at 80%. Sleep time protection holds at about 80% overnight and reaches 100% just before you wake — it was called Adaptive on One UI 6.1. Want a full charge every time? Turn Battery protection off.

One UI 7
Settings
Battery
Device care
Apps
Step 1
Battery
Power saving
Battery protection
Charging settings
Background usage limits
Step 2
Battery protection
Battery protection
BasicStops at 100%, resumes at 95%
MaximumStops at your chosen limit: 80–95%
Sleep time protection~80% overnight, full before you wake
Step 3
Battery › Battery protection › Maximum

Menu path, screen by screen: 1. Settings: Battery ←; Device care; Apps. 2. Battery: Power saving (off); Battery protection ←; Charging settings; Background usage limits. 3. Battery protection: Battery protection (on); Basic — Stops at 100%, resumes at 95%; Maximum — Stops at your chosen limit: 80–95% ←; Sleep time protection — ~80% overnight, full before you wake

The path on a Galaxy with One UI 7 or newer: Settings → Battery → Battery protection → Maximum.

Other brands have their own version: on Huawei and Honor the feature usually shows as Smart Charge or Custom limit in battery settings, on Motorola as Overcharge protection, and on OnePlus, Oppo and Realme as Smart charging or Optimized charging — the names differ from model to model. If you can't find it, search “charge” in the Settings search bar.

Tip· Need 100% just today?

Nearly every brand has a quick way: turn the limit off temporarily, or tap “resume charging” in the protection notification — on iPhone, hold the notification and tap Charge Now. You don't have to leave protection off for good.

Note· Heat can also stop charging at 80%

If the phone is too hot or too cold, charging is put on hold or slowed — on iPhone the “Charging On Hold” message appears. Move it somewhere cooler, out of direct sun, and charging resumes on its own at normal temperature.

It charges, but far too slowly

When a phone that should charge in an hour needs the whole night, the culprits are almost always the same few.

  • The charger is too weak. An old few-watt adapter can't match the fast-charge speed your phone supports — and on Xiaomi, unofficial chargers don't speak the fast-charge protocol at all. Which watts and standards matter: chargers and cables, explained.
  • The cable is thin, worn or unsuitable. Not all cables carry the same power — a worn one caps the current far below what the charger can give, even while looking intact.
  • You're charging from a PC or a car. USB ports on laptops, hubs or cars deliver far less current than a wall socket — Samsung notes fast charging may not work from a PC or a standard USB port.
  • The phone is hot. Every maker cuts the current at high temperatures to protect the battery — move it somewhere cooler and take the case off.
  • You're using it while it charges. With the screen on and games or video running, the consumption eats into the charge speed — Xiaomi measures its top speeds with the screen off.
  • It's nearly full. From around 80% up, every phone charges deliberately slowly to protect the battery — normal behaviour, not a fault.

Two settings can also hold the brake: on Samsung, go to Settings → Battery → Charging settings and check Fast charging is on (from the S23 series, super-fast charging is merged into it), and on some Xiaomi models there's Boost charging speed under Settings → Battery → Additional features.

Note

If the phone shows a message that the charging accessory isn't supported or certified — that's what the iPhone alert warns too — take it seriously: Apple lists the causes as a dirty port, a damaged accessory or a charger not designed for charging devices.

Only works at a certain angle: a worn port

Does the phone start charging only when you hold the cable in a certain position, or does the plug wobble and fall out? Two things can be at fault, in order of likelihood: lint compacted at the bottom of the port — so the step above, done properly — or worn port contacts.

The contact pins wear after thousands of plug-ins, faster if the phone spent a lot of time on the cable while in use or the plug was bent under weight. A worn port feels mechanical: the plug no longer clicks, sits loose and lets go at the slightest movement.

3D phone. Highlighted parts: charging port.

The charging port is a small part tied to the board by a signal flex — it's replaced on its own and it's one of the most common repairs.

The good news: replacing the port is routine work. What it involves, on models with the port on a flex and on those with the port on the board: charging port replacement. If the cable still wobbles or charging still cuts out after a proper clean, that's the repair that fixes it.

Where the home fixes end

The steps above cover the causes that fix themselves for free. Two situations are left for parts or bench measurements: the percentage sits still or drops while plugged in — a sign the battery no longer takes current or the charging circuit on the board is faulty — and a battery that's had it: it drains visibly faster than before, on any charger.

The symptoms and what they say, in short
What you seeWhat it usually isWhat you do
No reaction on any chargerDead cable or adapter, fully flat batteryAnother cable and socket, then 30 minutes of patience
Only works held at an angleCompacted lint or a worn portClean the port; if it doesn't help, port replacement
Stops at 80%A battery protection feature is onThe per-brand settings in the section above
Charges very slowlyWeak charger, worn cable, PC/car or heatThe right charger and cable, phone somewhere cool
Liquid alert or droplet iconMoisture in the portUnplug the cable, let it dry, charge wirelessly meanwhile
Percentage stuck or dropping on the chargerConsumption higher than input, battery or boardClose heavy apps; if it persists, a bench diagnosis
Gets properly hot while chargingWarm room, thick case or a faulty accessorySomewhere cooler, case off; if it keeps happening, service

Danger· The sign that changes everything

Bulging back cover, screen pushed outwards or a strange smell? Power the phone off and stop charging it — a swollen battery is not pressed, pierced or charged. What to do right away, step by step: hot phone and swollen battery.

Want to find the dead link yourself — cable, charger, port or battery? Follow the charging test step by step and check battery health; if there's no sign of life at all, see phone won't turn on. On the bench, a diagnostic tells you on the spot whether it's the port, the battery or the board — before you decide on a repair.

Frequently asked questions

Why does my phone only charge up to 80%?
Because a battery protection feature is on: a fixed limit (Samsung Maximum, Pixel Limit to 80%, iPhone Charge Limit, Xiaomi Smart charging) or an adaptive charge that finishes just before you unplug. The exact path for your brand is in the Stops at 80% section. Heat can put charging on hold at the same point too.
My phone only charges while I hold the cable in a certain position.
Clean the port first — compacted lint causes exactly this symptom and comes out at home, with the phone off and a wooden pick. If the plug still wobbles and charging drops at the slightest movement after cleaning, the port contacts are worn and the port needs replacing — settings won't help.
Can I charge the phone if the liquid warning is showing?
Not normally — the alert exists to protect the pins from corrosion. On iPhone there's an emergency option to override the detection, but Apple warns it can destroy the port for good. The safe workaround meanwhile: wireless charging, if your model has it.
How long before a fully drained phone shows signs of life?
Usually up to 30 minutes on a working charger before the battery icon or LED appears — the interval Apple gives too. Don't unplug it after two minutes to check. If nothing shows after 30–60 minutes, swap the cable and charger, then it's a job for a technician.
Why does my phone charge slowly overnight?
Most of the time the charger is too weak or you're charging from a PC or car port instead of a wall socket. The cable, room heat and using the phone while it charges all matter too. The last stretch, from 80% up, charges deliberately slowly on every model — that's normal.
Is it normal for the phone to get warm while charging?
Slightly warm, yes — especially on fast charging. Properly hot, no: at high temperatures every phone cuts the current or puts charging on hold to protect the battery. Move it somewhere cooler, out of the sun, and take the case off. If it heats up for no reason with no charger attached, the battery or board may be at fault — see hot phone and swollen battery.

Does your phone look different, or is something missing here?

Menus and buttons differ from model to model and change with updates. If these steps do not match your phone or you cannot find what you need, tell us your model and what you see on the screen: we will answer you and update the guide.

Checked against

Still not charging?

On the bench we measure whether it's the cable, the port, the battery or the board — and you hear what's worth repairing.