Connecting
Bluetooth headphones or speaker that will not connect
Short version
- Work in this order: charge the accessory and the phone, put the accessory in pairing mode, forget the old pairing and redo it, then restart both.
- Connecting to another phone or laptop instead of yours? Accessories prefer the last device used — turn Bluetooth off over there.
- Connected but silent: in the device's settings, switch Media audio back on.
- Asked for a PIN while pairing? The most common ones are 0000 and 1234.
- The last resort is a network settings reset — it erases Wi-Fi passwords and every pairing, but not your photos or apps.
Why it won't connect
Bluetooth remembers devices. After the first pairing, the phone and the earbuds recognise each other on their own — and that is also the problem: the earbuds have no idea you want them on your phone rather than on yesterday's laptop. They connect automatically to the last device they “heard”.
Connection: Yesterday's laptop via they went here → The earbuds. The earbuds via you look here (broken) → Your phone.
The second common cause: the earbuds are not in pairing mode, so the phone can't see them in the list at all. The third is more banal: battery. A dead case never enters pairing mode, and a bud at 0% shows up in the list but never truly connects.
The order that fixes most cases
Don't skip steps — each one removes one of the causes above. All of them take about 5 minutes:
Charge the accessory
Drop the earbuds in their case and leave them on charge for 20–30 minutes if they haven't been used in a while. Apple asks for the accessory to be on and fully charged before pairing — an LED that won't light at all usually means an empty battery, not a fault.
Put it in pairing mode
The phone can only see the earbuds while they are in pairing mode — usually a fast-blinking LED (on some models it alternates blue, red and green). How to enter it differs per maker: on Galaxy Buds3 you hold the button on the case for over 3 seconds, and on many cheap speakers and earbuds you hold the power button ~5 seconds from off. Can't find the button? Look up “pairing” in your model's manual.
PhoneMessagesBrowserCameraHold the case button ~3 s, until the LED flashes Gesture on the phone screen: Hold the case button ~3 s, until the LED flashes.
Turn Bluetooth off on the other devices
Nearby phones and laptops that used the earbuds before fight over them. Switch Bluetooth off on those — or shut them down entirely — and only then retry pairing.
Forget the old pairing and redo it
If the accessory was paired before, remove it from the phone's Bluetooth list and pair it again as if it were new. The exact steps for each brand are in the next section.
Restart both
A restart clears small Bluetooth glitches on both sides. On the phone: quick panel → power icon → Restart (per-brand button combos are in the force-restart guide). The accessory “restarts” by leaving the buds in the closed case for ~10 seconds.
Tip· On Android with Fast Pair
Note
Forget the old pairing, then pair again
A corrupt pairing is the classic cause of “I can see it in the list, but it won't connect”. Removing it touches nothing else — it just makes the phone forget what it knew about that accessory. Pick your brand:
Menu path, screen by screen: 1. Settings: Connections — Wi-Fi • Bluetooth • SIM manager ←; Connected devices; Notifications; Display; Battery. 2. Connections: Wi-Fi — On; Bluetooth — On ←; Airplane mode (off); Data usage; Mobile Hotspot and Tethering. 3. Bluetooth: Bluetooth (on); [Paired devices] Galaxy Buds3 Pro — Connected ←; [Available devices] JBL GO 3
Open the path to Bluetooth
On a Galaxy, the path is Settings → Connections → Bluetooth.
Tap the gear and Unpair
Tap the Settings icon (the gear) next to the device's name, then Unpair. The connection history is deleted — the earbuds disappear from the paired-devices list.
Pair again
With the earbuds in pairing mode, pick their name from the available devices list and confirm with Pair.
Asked for a PIN? Try 0000 or 1234 — the standard codes Google itself suggests.
Pixel Buds Pro 2 will be removed from this phone.
Menu path, screen by screen: 1. Settings: Network & internet — Wi-Fi, mobile data; Connected devices — Bluetooth, pairing ←; Apps; Notifications; Battery. 2. Connected devices: Connection preferences — Bluetooth, Android Auto, NFC; [Saved devices] Pixel Buds Pro 2 — Connected ←; Kitchen speaker — Not connected. 3. Device details: Media audio (on); Phone audio (on); Forget ←. 4. Forget device?. Pixel Buds Pro 2 will be removed from this phone. [Cancel] [Forget device]
Open the path to saved devices
On Pixel and near-stock Android (Motorola, Nokia), the path is Settings → Connected devices → Saved devices.
Forget it and confirm
Tap the gear next to the name, then Forget and confirm with Forget device. On some versions the button is called Remove.
Pair again
With the earbuds in pairing mode, tap Pair new device and pick their name when it shows.
Menu path, screen by screen: 1. Settings: Wi-Fi — HomeNet; Mobile networks; Bluetooth ←; Portable hotspot; More connectivity options; Lock screen. 2. Bluetooth: Bluetooth (on); [Paired devices] Redmi Buds 6 — Connected ←; [Available devices] JBL GO 3
Open Bluetooth
On HyperOS, the path is Settings → Bluetooth.
Tap the arrow and Unpair
Tap the arrow › next to the device's name, then Unpair. The earbuds disappear from the paired-devices list.
Pair again
With the earbuds in pairing mode, tap their name in the available-devices list and confirm the pairing.
On Redmi Buds 6, you reset the earbuds by holding the case button for over 10 seconds until the LED flashes white — it erases every old pairing. On other models the procedure differs — check their manual for “reset”.
Menu path, screen by screen: 1. Settings: Airplane Mode (off); Wi-Fi — HomeNet; Bluetooth — On ←; General. 2. Bluetooth: Bluetooth (on); [MY DEVICES] AirPods Pro — Connected ←; [OTHER DEVICES] JBL GO 3. 3. AirPods Pro: Disconnect; Forget This Device ←; Name — AirPods Pro
Open Bluetooth in Settings
On iPhone, the path is Settings → Bluetooth.
Tap ⓘ and Forget This Device
Tap the ⓘ (More Info) icon next to the accessory, then Forget This Device and confirm with Forget Device.
For AirPods, forgetting propagates to every device signed in to your Apple Account — they need re-pairing everywhere.
Pair again
Put the accessory in discovery mode, then tap its name when it appears onscreen below the devices list. The iPhone needs to be within ~10 metres of the accessory.
Connected, but no sound (or bad sound)
“Connected” in the list does not guarantee the sound actually flows. Inside the device's settings are two switches that decide what travels over Bluetooth: the music and the calls. Check them first:
Phone screen: Device details: Media audio (off) ←; Phone audio (on)
Only one earbud playing? Put both buds in the case, wait ~10 seconds and take them out together. If that doesn't help, check the charging contacts in the case — grime on them is the classic cause of “dead” earbuds. The last step is resetting the buds: on Redmi Buds 6 you hold the case button over 10 seconds until it flashes white; for other models look for “reset” in the accessory's manual.
- Delay in video — Bluetooth has a small built-in delay. If it's only a fraction of a second it's normal; if lips are completely off the sound, forget and re-pair, or look for a “game mode” in the earbuds' app.
- Quiet volume at max — many earbuds have their own volume, separate from the phone's. Raise it from the earbud controls or the maker's app.
- Calls sound metallic — during calls Bluetooth switches to a lower-quality channel than for music; that's a limit of the standard. If it's unbearable, check that the earbud's mic isn't covered or dusty.
- Cuts out or stutters — Bluetooth reaches ~10 metres in theory, but walls, your own body and congestion on the 2.4 GHz band shorten it. Keep the phone close and away from the Wi-Fi router.
| Symptom | Frequent cause | What to do |
|---|---|---|
| Doesn't show in the list at all | not in pairing mode, or out of battery | hold the pairing button until the LED flashes; leave it charging |
| Shows up, but pairing fails | a stuck old pairing, or it's tied to another device | forget it and re-pair; turn Bluetooth off on the other device |
| Connected, but no sound | media profile switched off | turn on “Media audio” in the device's settings |
| Only one earbud plays | dirty contact, flat battery or a corrupt pairing | both in the case for 10 s, clean the contacts, re-pair or reset |
| Drops out when you move | distance, interference, battery | keep the phone close, charge the accessory, away from routers |
| Won't connect in the car | the car's or the phone's list is full | clear old phones from both, then pair again |
In the car, in short
Clear the lists on both ends
Remove old phones from the phone (as above) and from the car's own system — the procedure is in its manual. Full lists block a new pairing.
Search for the phone from the car's menu
On some systems the pairing starts from the car's screen, not the phone. Put the car in pairing mode and keep the phone's Bluetooth screen open.
Confirm the codes and contact access
Check that the PIN shown on the car's screen matches the one on the phone, and confirm. Then tick Allow access to your contacts and call history — without it, your phonebook never reaches the car's display.
Connection: The phone via music + calls → The car's system.
Note
Last resort: reset network settings
Warning· What the reset erases
The path — and exactly what it erases — differs per brand: on Pixel it only touches Wi-Fi and Bluetooth, on Samsung other saved connections too, on Xiaomi mobile networks as well, and on iPhone cellular settings, VPN and APN. Pick your brand:
Menu path, screen by screen: 1. Settings: Notifications; Display; Battery; Apps; General management — Languages, backup, reset ←. 2. General management: Date and time; Default apps; Reset ←. 3. Reset: Reset mobile network settings; Reset Wi-Fi and Bluetooth settings ←; Factory data reset
Open the Reset menu
The path is Settings → General management → Reset → Reset Wi-Fi and Bluetooth settings.
Confirm the reset
Tap Reset Wi-Fi and Bluetooth settings, then Reset settings — you may be asked for your lock-screen PIN. Afterwards, re-pair the earbuds and re-enter your Wi-Fi password.
On some models and older versions the option is called Reset network settings — same effect.
Menu path, screen by screen: 1. Settings: Notifications; Battery; Storage; System — Languages, gestures, time, backup ←. 2. System: System update; Reset options ←. 3. Reset options: Reset Bluetooth & Wi‑Fi ←; Reset Mobile Network Settings; Erase eSIMs; Reset app preferences; Erase all data (factory reset)
Open Reset options
The path is Settings → System → Reset options → Reset Bluetooth & Wi-Fi.
Confirm the reset
Tap Reset Bluetooth & Wi-Fi and confirm. Careful not to pick the last row — Erase all data is a factory reset and wipes the phone.
Menu path, screen by screen: 1. Settings: Wi-Fi — HomeNet; Mobile networks; Bluetooth; Portable hotspot; More connectivity options ←; Lock screen. 2. More connectivity options: NFC (off); Android Auto; Reset Wi-Fi, mobile networks, and Bluetooth ←
Open connectivity options
On HyperOS, the path is Settings → More connectivity options → Reset Wi-Fi, mobile networks, and Bluetooth. On some MIUI versions the option lives under Connection & sharing.
Confirm the reset
Tap the reset option, then
Reset settingsand confirm withOK. It also forgets saved mobile networks — photos and apps are untouched.
Menu path, screen by screen: 1. Settings: Airplane Mode (off); Wi-Fi — HomeNet; Bluetooth — On; General ←. 2. General: About; Software Update; AirDrop; Transfer or Reset iPhone ←. 3. Transfer or Reset iPhone: Reset ←; Erase All Content and Settings. 4. Reset: Reset All Settings; Reset Network Settings ←
Open Reset under General
The path is Settings → General → Transfer or Reset iPhone → Reset.
Choose Reset Network Settings
Confirm with your passcode. Do not pick “Erase All Content and Settings” — that one wipes the phone completely.
On other brands (Huawei, Honor, Motorola, Oppo, OnePlus) search for reset in the Settings search bar — the option has an almost identical name everywhere and usually lives in the system menu. If your menu looks different, write to us through the form at the end of the page.
When the phone is at fault
The acid test: does the accessory connect to another phone without trouble? Then your phone is the culprit. Here's what else to try before a repair shop:
0 of 5 done
Apple states the same rule for iPhone: if the Bluetooth switch is greyed out or won't stay on and no accessory connects, it's a service matter, not a settings one.
Frequently asked questions
Why does my phone see the earbuds but won't connect?
The earbuds connect to a laptop or another phone, not mine. What now?
Only one earbud plays. Is it broken?
Volume is low even at maximum. Why?
The sound lags in videos. Can it be fixed?
Will I lose data if I reset network settings?
How far does Bluetooth reach?
Does your phone look different, or is something missing here?
Menus and buttons differ from model to model and change with updates. If these steps do not match your phone or you cannot find what you need, tell us your model and what you see on the screen: we will answer you and update the guide.
Checked against
- Google — Remediază problemele legate de Bluetooth pe Android
- Google — Găsește și configurează dispozitive Bluetooth
- Apple — Dacă un accesoriu Bluetooth nu se conectează la iPhone sau iPad
- Apple — Conectarea iPhone-ului la accesoriile Bluetooth
- Apple — Dacă nu te poți conecta la Wi-Fi pe iPhone sau iPad
- Samsung — Cum să remediezi problemele de conexiune Bluetooth
- Xiaomi — How to reset Wi-Fi, mobile networks and Bluetooth
- Xiaomi — How to clear the pairing records of REDMI Buds 6
Related guides
Wi-Fi or Bluetooth won't turn on, or turns itself off
Wi-Fi switch grey or dropping by itself? The tests that show whether it's a setting, the router or the chip on the board.
15 min · Anyone can do it
Android Auto and Apple CarPlay: setup and common problems
The data cable, the car's right USB port and re-pairing — what actually works when Android Auto or CarPlay misbehaves.
15 min · Anyone can do it
People can't hear you on calls, or you can't hear them
When you can't hear the other person or they can't hear you: the speaker test, earphones and a voice memo, then the free fixes, step by step.
10 min · Anyone can do it
Sending photos and files quickly between phones and to a PC
Quick Share, AirDrop and what works between them — photos and files at original quality between phones and to a computer, no cable.
10 min · Anyone can do it
Devices still won't pair?
It may be a hardware issue — the port, antenna or wireless module.